A hidraulikus prés alapvető paraméterei
Az alapvető paraméterek a hidraulikus prés alapvető műszaki adatai, melyeket a hidraulikus prés technológiai felhasználása és szerkezeti típusa szerint határoznak meg. Ez tükrözi a hidraulikus prés munkaképességét és jellemzőit, valamint alapvetően meghatározza a hidraulikus prés körvonalméretét és teljes bruttó tömegét. Az alapvető paramétereket a felhasználó választja ki. A vásárlás fő alapja. Mik tehát a hidraulikus prés alapvető paraméterei? Hogyan lehet megérteni és kiválasztani a hidraulikus prés paramétereit? Ma a közös három-gerenda négy-oszlopos hidraulikus prés alapvető paramétereit fogom kidolgozni Önnek.
1. Névleges erő (KN)
The nominal force is generally the main parameter of the hydraulic press, which reflects the working capacity of the hydraulic press. The nominal force is the maximum working pressure that the hydraulic press can nominally issue, and is numerically equal to the product of the maximum liquid pressure and the total area of the working plunger (piston radius) R²πpressure gauge value (system pressure)
Note: 1MPa≈100N
Take 60T calculation as an example: cylinder diameter φ180mm system pressure 25MPa (for high pressure)
90903.1425÷10000 (unit conversion)
2. Maximális belmagasság (nyitási magasság)
The maximum clearance distance refers to the distance from the upper surface of the table to the lower surface of the movable beam when the movable beam stops at the upper limit position. The maximum clearance distance reflects the size of the working space of the hydraulic press in the height direction. It should be determined by process factors such as the height of the mold and the corresponding backing plate, the size of the working stroke, and the size of the space required for placing the blank and taking out the workpiece. The maximum clearance has a great influence on the overall height of the hydraulic press, the length of the column, the stability of the hydraulic press body and the height of the installation workshop. The maximum clearance distance of the single-arm hydraulic press is the distance from the lower plane of the indenter to the upper surface of the table.
3. Maximális löket
The maximum stroke refers to the distance from the lower plane of the column guide sleeve of the movable beam to the upper plane of the column travel limit sleeve when the movable beam is at the upper limit position, that is, the maximum distance that the movable beam can move. The maximum stroke should be determined according to the required maximum working stroke during the workpiece forming process.
4. Asztal mérete (hossz szélessége)
The workbench is generally the place where the mold is placed. The size of the worktable refers to the effective size that can be used on the worktable, and the size of the worktable depends on the plane size of the mold and the arrangement of the process.
5. A torok mélysége (egy-oszlopos hidraulikus prés)
Refers to the distance from the center of the single-column hydraulic press head to the inner surface of the frame.
6. Visszatérő erő
The return force refers to the weight of the movable part, the force required for the return process (such as the draft force, the lifting force of the chopping knife), etc.
7. A mozgatható gerenda mozgási sebessége (csúszka sebessége): felosztható munkalöket sebességére, üresjárati löket (folyadék töltőlöket) sebességére és visszatérési sebességre.
The idle travel and return travel can generally be higher to improve productivity, but too fast will cause shock and vibration when stopping or reversing.
Háromféle sebesség létezik:
⑴Constant speed (eternal speed): rising speed, falling speed (using electro-hydraulic reversing valve)
⑵Differential: ①Fast down, slow back ②Slow down, fast back, idle descending, pressing, and returning (with cartridge valve) ③Up and down equal velocity
(3) Gyors (folyadéktöltő rendszer): Szándékosan fel van szerelve sebességnövelő-hengerrel is, ahelyett, hogy saját súlyára hagyatkozna az ejtés során;
8. Névleges kilökőerő és kilökési löket
The function of the ejector cylinder is to eject or stretch, and the power and stroke safety of the ejector are determined by the process requirements;
9. Az Y27 egy-működésű lapos feszítő hidraulikus présnek ismernie kell a hidraulikus betéterőt és a hidraulikus betétlöket paramétereit is.
10. Az Y28 dupla-működésű laprajzoló hidraulikus présnek ismernie kell a húzóerő paramétereit, a nyersdarabtartó erőt, a húzócsúszka löketét, a nyersdarab tartó löketét, a nyitási magasságot is. rajzcsúszkát és az üres tartó nyitási magasságát.
11. Az egy-oszlopos hidraulikus prés tokmány típusú vagy felső csúszka (nyomólemez típusú) szerkezet, szükséges-e a munkaasztal korrigálása stb.
12. Műveletsor (akciófolyamat) Az ügyfél biztosítja a préselési folyamat sorrendjét és a folyamatkövetelményeket (folyamatkövetelmények).






